Site Failure Recovery

Restore an Unhealthy Peer to Site Replication

Site replication keeps two or more Buckit deployments in sync with IAM policies, buckets, bucket configurations, objects, and object metadata. If a peer site fails, such as due to a major disaster or long power outage, you can use the remaining healthy site(s) to restore the replicable data.

The following procedure can restore data in scenarios where site replication was active prior to the site loss. This procedure assumes a total loss of one or more peer sites versus replication lag or delays due to latency or transient deployment downtime.

1. Remove the failed site from the Buckit site replication configuration using the bm admin replicate rm command with the --force option.

   The following command force-removes an unhealthy peer site from the replication configuration:

   bm admin replicate rm HEALTHY_PEER UNHEALTHY_PEER --force
   

   • Replace HEALTHY_PEER with the alias of any healthy peer in the replication configuration

   • Replace UNHEALTHY_PEER with the alias of the unhealthy peer site

   All healthy peers in the site replication configuration update to remove the unhealthy peer automatically. You can use the bm admin replicate info command to verify the new site replication configuration.

2. Deploy a new Buckit site following the site replication requirements.

   • Do not upload any data or otherwise configure the deployment beyond the stated requirements.

   • Validate that the new Buckit deployment functions normally and has bidirectional connectivity to the other peer sites.

   • Ensure the new site matches the server version on the existing peer sites

   Warning

   The bm admin replicate rm --force command only operates on the online or healthy nodes in the site replication configuration. The removed offline Buckit deployment retains its original replication configuration, such that if the deployment resumes normal operations it would continue replication operations to its configured peer sites.

   If you plan to re-use the hardware for the site replication configuration, you must completely wipe the drives for the deployment before re-initializing Buckit and adding the site back to the replication configuration.

3. Add the replacement peer site to the replication configuration.

   Use the bm admin replicate add command to update the replication configuration with the new site:

   bm admin replicate add HEALTHY_PEER NEW_PEER
   

   • Replace HEALTHY_PEER with the alias of any healthy peer in the replication configuration

   • Replace NEW_PEER with the alias of the new peer

   All healthy peers in the site replication configuration update for the new peer automatically. You can use the bm admin replicate info command to verify the new site replication configuration.

4. Resynchronize the new peer with bm admin replicate resync.

   bm admin replicate resync start HEALTHY_PEER NEW_PEER
   

   • Replace HEALTHY_PEER with the alias of any healthy peer in the replication configuration

   • Replace NEW_PEER with the alias of the new peer

5. Validate the replication status.

   Use the following commands to track the replication status:

   • bm admin replicate status - provides overall status and progress of replication

   • bm replicate status - provides bucket-level and global replication status

Active Bucket Replication Resynchronization

For scenarios where bucket replication was in place prior to the failure, you can use bm replicate resync to restore data to a new site. Create a new site to replace the failed deployment, then synchronize the data from an existing, healthy, bucket replication-enabled deployment to the new site.

1. Deploy a new Buckit site.

2. Set up IAM and users as needed.

3. On the site with data, create a new remote target using the bm admin bucket remote add command and record the ARN from the output.

4. From the site with the data, use the bm replicate resync start command with the ARN from the previous command to rebuild the bucket on the new site.

5. Wait for re-synchronization to complete (use bm replicate resync status to check).

6. Set up bucket replication rule(s) from the new Buckit site to the existing target bucket(s).

7. (Optional) Delete the bucket replication rules from the target deployment(s) to restore an active-passive replication scenario.

Passive Bucket Replication Resynchronization

Bucket replication can directly restore the site contents by performing a replication from the target bucket(s) to a new Buckit site.

As a passive process, bucket replication may not perform as quickly as desired for a site recovery scenario.

Bucket replication relies on the standard replication scanner queue, which does not take priority over other processes. For recovery procedures with stricter SLA/SLO, use the active bucket replication process with bm replicate resync command as described above.

Bucket replication rules copy the object, its version ID, versions, and other metadata to the target bucket. Buckit can restore the object with all of these attributes to a new Buckit site if bucket replication had already been in use prior to the site loss.

1. Deploy a new Buckit site.

2. Set up IAM and users as needed.

3. On the remaining target bucket deployment(s), create bucket replication rule(s) for each bucket to the new Buckit site.

4. Wait for replication to complete.

5. Set up bucket replication rule(s) from the new Buckit site to the existing target bucket(s).

6. (Optional) Delete the bucket replication rules from the target deployment(s) to restore an active-passive replication scenario.

   Do not delete the bucket replication rules from the deployments used to recover data if you prefer to keep an active-active replication between the buckets. In active-active replication, changes to the objects at either location affect the objects at the other location.

Mirroring

Buckit’s mirroring copies an object from any S3 compatible storage system.

Mirroring only copies the latest version of each object and does not include versioning metadata, regardless of the source. You cannot restore those attributes with this method.

Use bm mirror in situations where you need to restore only the latest version of an object. Use bucket replication or site replication where those methods were already in use if you are copying from another Buckit deployment and wish to restore the object’s version history and version metadata.

1. Deploy a new Buckit site.

2. Set up IAM and users as needed.

3. Create buckets on the new site.

4. Use the bm cp CLI command to copy the contents from the mirror location to the new Buckit site.